freehas.blogg.se

Type2 board vendor name 1 type2 board product name15
Type2 board vendor name 1 type2 board product name15













  1. #Type2 board vendor name 1 type2 board product name15 verification
  2. #Type2 board vendor name 1 type2 board product name15 software

MA5683T(config-gpon-lineprofile-13)#gem add 1 eth tcont 1 //Define GEM PORT 1 with tcont 1 binding. MA5683T(config-gpon-lineprofile-13)#tcont 1 dba-profile-id 13 //Define tcont with DBA template binding.By default, tcont 0 with DBA template 1 binding,don't need to config.Here,designate tcont 1 with DBA 13 template binding.

type2 board vendor name 1 type2 board product name15

MA5683T(config)#ont-lineprofile gpon profile-id 13 profile-name HG8240 //Define ONT route and designate name MA5683T(config)#dba-profile add profile-id 13 profile-name HG8240 type2 assure 10240 //Define DBA model number,and designate DBA model name. MA5683T(config-if-vlanif1000)#ip address 192.168.100.10 255.255.255.0Īt the same time, need to configure the corresponding onu management address distributed function. MA5683T(config)#interface scun 0/7 //Into the uplink MA5683T(config)#port vlan 1000 0/7 0 //Increase uplink MA5683T(config)#vlan 1000 smart //management VLAN Service-port vlan 1001 adsl 0/0/30 vpi 0 vci 35 rx-cttr 6 tx-cttr If in the fttb networking,Olt side only need to configure the line template, do not need to configure PoC template,add onu use snmp protocol。 Service-port vlan 1001 epon 0/0/1 ont 0 multi-service user-vlan 1001 Ont add 1 0 mac-auth 0000-0000-0001 oam ont-lineprofile-id 10 ont-srvprofile-id 11 Note: Must be based on the ONT actual number of port configuration,if you don't know it,you can enter the Epon veneer mode using the command "disp ont capability" view. Ont-srvprofile epon profile-id 11 profile-name HG8240 Ont-lineprofile epon profile-id 10 profile-name HG8240 Vlan 100 smart \\Add network management vlanĪdd the corresponding vlan to the uplink:ĭba-profile add profile-id 10 type2 assure 20480 MA5683T(config)#snmp-agent community write private MA5683T(config)#snmp-agent community read publicġ.3、Create and uplink transmission PoC VLAN

#Type2 board vendor name 1 type2 board product name15 software

If you need network management software management, then you need to add the following command If the 0/8 0 port is connected, you can use the huawei123 telnet this address Huawei landing.

type2 board vendor name 1 type2 board product name15

For the board is unconfirmed,board of hardware running indicator light is normal,but the PoC port doesn't work. MA5683T(config)#board confirm 0 //To automatically discover board, need to be confirmed after a board can be used. SlotIDBoardNameStatus SubType0 SubType1 Online/Offline. Check the equipment state of board,the most commonly used commands. After if you want to start or insert a new board need the following,autofind is newly inserted PoC board MA5683T(config)#display board 0 User's Appended Info(<=30 chars):HuaweiAdm //Add a description, not set.Īdding user succeeds Repeat this operation? (y/n): Permitted Reenter Number(0-4):1 //Set the user name can repeat logins, general requirements for 1 times. Administrator:3 //Select the user permissions User profile name(<=15 chars):root //nter the user management levelġ.

#Type2 board vendor name 1 type2 board product name15 verification

Enter part of the actual not visibleĬonfirm Password(length):huawei123 // Verification the password again User Password(length):huawei123 //Required to enter your password. User Name(length):huawei //Setting the user name

type2 board vendor name 1 type2 board product name15

MA5683T(config) #terminal user name //Add user operation huawei MA5683T(config)#sysnameSJZ-HW-OLT-1 //device-naming (Usually when to start the configuration) MA5683T#config //Enter the terminal configuration mode through the console,login user name root,password admin.If the device is a twin-engine,connect bright green light board ACT.















Type2 board vendor name 1 type2 board product name15